Dexaplan VT 623 Manuel d'utilisateur télécharger pdf (Page 5)

First use

Operation

Plug the mains adapter [12] into a mains power socket. The operating

status LED [35] lights green and the nameplate cover [20] is

illuminated from the back.

Remove the protective film from the monitor [33].

The video door entry system is now ready for operation.

A visitor presses the doorbell button [21] of the outdoor station. A chime

sounds from the indoor station. The camera image is displayed on the

monitor [33] and the operating status LED [35] lights red. It can now be

heard on the indoor station what is said at the outdoor station.

If the visitor presses the doorbell button again, the chime sounds again.

Press the talk button [36] to speak to the visitor. The LED of the

talk button flashes blue.

Now speak into the microphone [39]. The visitor hears you by means

of the loudspeaker [19] of the outdoor station and can talk to you

using the microphone [22] of the outdoor station. You hear the visitor

by means of the loudspeaker [34] of the indoor station.

Press the talk button again to end the conversation; otherwise

the connection will end automatically after 4 minutes. The LED of the

talk button stops flashing and the monitor image disappears.

If you do not react to the visitor pressing the doorbell button, the monitor

image disappears after approx. 60 seconds

You can only start the talk function when the monitor image is activated.

The chime and the conversation are relayed to a powered loudspeaker if

connected. If the powered loudspeaker has a volume control, you can

adjust the volume independently of the indoor station volume.

If a door opener is connected, you can unlock the door / gate as follows

With a latching door opener the door or gate remains open after the signal.

Press the door opener button [37]. The gate or the door is locked

again after it has been opened and closed again.

Keep the door opener button [37] pressed until the visitor has

opened the door. The door remains unlocked for the period in which

you keep the button pressed.

Release the door opener button and the door opener locks

immediately.

While the door opener button is pressed, the LED of the door opener button

flashes blue for approx. 2 seconds, the monitor image disappears for a

short time, “NO SIGNAL” is displayed briefly on the monitor and the

nameplate is not illuminated.

Unlocking the door / gate is only possible when the monitor image is

activated.

Note:

Door opener (optional)

Latching door opener

Non-latching door opener

Carefully make a hole using a pointed object in one of the

predetermined breaking points of the grommet [24].

Guide the connection cable [14] through this hole.

If required, make a second hole for the cable of an optional door

opener and guide the cable through this hole.

Connect the connection cable [14] to the terminals of the outdoor

station [59, 60] and the indoor station [55, 56] according to the

connection diagram (see Fig. I). Pay attention here to the wire

markings and the polarity (A to A, B to B).

If desired, connect an optional door opener [62] (see next chapter).

Replace and screw down the terminal cover on the outdoor station.

If desired, install an optional door opener [62] (not included in the

package contents) at the desired location according to the instructions

of the manufacturer.

Connect it to the terminals [57] and [58] of the outdoor station with a

two-core cable (polarity-independent) according to the connection

diagram (see Fig. I).

Connect an optional powered loudspeaker [48] (not included in the

package contents), e.g. a PC speaker, to the terminals [53] and [54]

of the indoor station with a two-core cable according to the connection

diagram (see Fig. I). Pay attention to the polarity for the connection.

Connect the low-voltage connector [13] to the connection [50].

For cable routing along the wall: Guide all connected cables through

the cable opening [25].

Slide the outdoor station [1] at an angle upwards into the wall bracket

and push it into place.

Fix the outdoor station to the wall bracket through the two holes [30]

with two of the fixing screws [4].

For cable routing through the wall: Place the connection cable [14]

into the cable channel [51].

For cable routing along the wall: Place the mains adapter cable into

the cable channel [51].

Slide the indoor station [2] at an angle upwards into the wall bracket

and push it into place.

Fix the indoor station to the wall bracket through the hole [47] with

one fixing screw [4].

Hang the indoor station [2] on the two protruding screw heads in the

wall using the keyhole slots [49].

Connecting an optional door opener

Connecting optional powered loudspeaker

Connecting the mains adapter to the indoor station

Finishing the outdoor station mounting

Finishing the indoor station mounting

Finishing the wall mounting

Screwing to the wall

Hanging on the wall

GB / IE - 7

1 2 3 4 5 6 7 8 9 10 ... 21 22

Commentaires sur ces manuels

Pas de commentaire

Dexaplan VT 623 Manuel d'utilisateur Page 5

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la maison Dexaplan VT 623